Tabber, inserter, feeder, inkjet base: what each machine in a mail shop does

By the Tri-State Equipment parts desk. Updated November 16, 2026.

If you are new to a mail shop floor, or you are a printer adding mailing services, here is what each machine does and where it sits in the line. We sell, service and stock parts for all of them.

In short

  • A mail line is usually a feeder, a transport base, and one or more stations on it: inkjet, tabber, labeler or stamp affixer.
  • Folders and inserters prepare the piece; cutters handle forms before or after printing.
  • At the end of the line, strappers, wrappers and case sealers get the work out the door.
  • Each section below says what the machine does and where it fits.

Friction feeder

The start of most lines. It separates one piece from a stack and feeds it into the next machine at a steady rate, and it can count into batches. Used ahead of tabbers, inkjet bases, inserters and labelers, and on packaging lines to feed cards or inserts. Streamfeeder and Straight Shooter are the lines we carry.

Inkjet addressing base (transport)

A conveyor base that carries each piece under one or more print heads. Prints the address, the barcode and any variable text from the mailing list. The print system on the base (cartridge or bulk ink) decides which ink you run; our ink guide covers that. Kirk-Rudy bases are the backbone of most of the shops we serve.

Tabber

Applies wafer seals to hold a folded self-mailer, booklet or double postcard closed. Often combined with an inkjet system on the same base so the piece is tabbed and addressed in one pass. The seal count and placement follow USPS rules; see our tabs guide.

Folder

Folds flat sheets into letters, self-mailers and brochures. Buckle folders handle most mail work; knife folders are for heavier stock and more complex folds. Baum, MBO and Stahl folders are the ones we see most and keep parts for.

Inserter

Takes sheets or folded pieces, folds as needed, inserts them into envelopes, seals the flap and stacks the output. Swing-arm inserters handle a wide range of envelope sizes; high-speed systems add reading and matching so the right insert goes in the right envelope. MailCrafters, Bell and Howell and BlueCrest are the inserters we service.

Labeler

Applies labels: addresses printed on label stock, or promotional and compliance labels, at speed and in register.

Stamp affixer

Applies live postage stamps from a coil or sheet, for mailings where a real stamp lifts response. Postmatic is the line we carry.

Cutter and forms handling

For continuous forms and roll-fed work, a cutter or slitter-merger cuts and collates before the pieces go to the inserter. Spedo makes the ones we sell.

End of the line: strappers, wrappers and case sealers

Once pieces are in trays or cartons, a strapper bands them, a stretch wrapper secures the pallet, and carton sealers and tape applicators close boxes. These come from the packaging side of the business; see our packaging page.

Putting a line together

A typical self-mailer line: folder, friction feeder, tabber with inkjet, stacker, strapper. A typical envelope line: inserter, inkjet base for addressing, stacker, tray. The right configuration depends on volume, piece size and how often the job changes. Tell us what you mail and how much, and we will lay out a line, new or refurbished.

Questions we get

What is a tabber?

A machine that applies wafer seals (tabs) to the open edge of a folded mailpiece so it runs on USPS automation. Many tabbers also carry an inkjet print system, so one pass tabs and addresses the piece.

What is the difference between a tabber and a labeler?

A tabber applies small adhesive seals to close a piece. A labeler applies printed labels, such as addresses or promotional labels, anywhere on the piece. Kirk-Rudy makes both, and some bases can be fitted for either.

Do I need an inserter or a folder?

A folder folds sheets. An inserter folds (or takes folded pieces) and puts them into an envelope, then seals it. If your work ends up in an envelope, you need an inserter; if it mails as a self-mailer, you need a folder and a tabber.