Friction feeder troubleshooting: doubles, misfeeds and skew

By the Tri-State Equipment parts desk. Updated November 16, 2026.

A friction feeder has one job: take the bottom piece off the stack and send exactly one piece downstream, square, every cycle. Feed belts pull the bottom piece forward; a gate and separator hold back everything above it. Nearly every feeding problem is the balance between those two forces going wrong, and most of the fixes are adjustments an operator can make in a few minutes.

In short

  • Doubles: gate too open, stack too heavy, worn separator, or pieces sticking together.
  • Misfeeds: gate too tight, glazed belts, or the stack not sitting flat on the belts.
  • Skew: guides loose or out of square, curled stock, or belts worn unevenly.
  • Change one setting at a time, and run 20 to 30 pieces at production speed before judging the result.
Stack of pieces Wedge lifts the back of the stack Feed belts pull the bottom piece Gate and separator: gap set to one piece One piece out
How a friction feeder separates one piece: belts pull from below, the gate holds back the rest, the wedge keeps the stack from pressing too hard.

Symptom, likely cause, fix

Symptom Most likely cause What to do
Two pieces at once Gate too open for the piece Close the gate in small steps until doubles stop
Doubles that come and go Stack weight pressing pieces into the belts Load less, or raise the wedge so the stack bears less on the belts
Doubles even with a tight gate Separator worn flat or shiny Replace the separator
Pieces stuck together Static, humidity, fresh ink or coating Fan and jog the stock, let printed work cure, acclimate stock to the room
Feeder runs but nothing comes out Gate too tight after a job change Open the gate slightly and test
Intermittent misses Belts glazed or dirty Clean with the cleaner the manual specifies; replace if they stay shiny
Misses at the back of the stack Stack not sitting flat on the belts Reset the back guide and wedge
Pieces arrive crooked Side guides loose or out of square Set guides to the piece with just enough room to drop freely
Crooked on one side only Belts worn unevenly across their width Replace the belts as a set
Unpredictable feeding Curled stock Reverse-curl before loading, or load curl-down

Doubles, in more detail

The gate is the first thing to check, because every job change moves it. Close it until doubles stop, then test a few more pieces; a gate set right lets one piece through cleanly without stalling.

If the gate is right and doubles continue, look at stack pressure. A tall, heavy stack presses the bottom pieces into the belts hard enough that the second piece gets dragged along with the first. The wedge (or back support) exists to lift the trailing edge and take weight off the belts. Raising it, or loading a shorter stack, often stops doubles that no gate setting would.

Last, the stock itself. Freshly printed or coated pieces can bond to each other, and dry winter air builds static. Fanning and jogging the stack before loading breaks those bonds; letting printed work sit long enough to cure prevents them.

Misfeeds, in more detail

A feeder that cycles without delivering a piece is usually not gripping. Feed belts glaze with paper dust and coating over time. Clean them with the cleaner your manual specifies (not a general solvent, which can harden rubber), and if they stay shiny or show cracks, replace them. A missed piece can also come from a stack that is not resting flat: a curled piece or a back guide set too far forward lifts the bottom of the stack off the belts.

Set up every job the same way

  1. Set the side guides to the piece, square and parallel.
  2. Set the gate with a few test pieces, closing until doubles stop.
  3. Set the wedge and back guide so the stack sits flat and light on the belts.
  4. Run 20 to 30 pieces at production speed and watch the output before starting the count.
  5. Write the settings down for that job. The next run starts at the right place.

When it is a repair, not an adjustment

If a setting will not hold, or you keep moving the gate to stay even, a part is wearing: separator, feed belts, drive belt or a bearing. We stock feeder parts and belts for the feeders we service, and a 20-second phone video of the problem usually tells our technicians which part to ship. See what to send us when a machine is down.

Questions we get

Why is my friction feeder pulling doubles?

In order of likelihood: the gate is set too open for the piece, the stack is pressing too hard on the feed belts, the separator is worn, or the pieces are sticking together from static, humidity or fresh ink. Close the gate in small steps, lighten the stack, then check the separator.

Why does my feeder skip pieces?

Usually the gate is too tight for the piece, the feed belts are glazed and no longer grip, or the stack is not resting flat on the belts. Open the gate slightly, clean or replace the belts, and reset the wedge and back guide.

Why are pieces feeding crooked?

Side guides that are loose or not parallel, a leaning stack, curled stock, or feed belts worn more on one side. Square the guides to the piece, reload the stack evenly and check the belts across their full width.

How often should feeder belts be replaced?

When cleaning no longer restores grip. Belts that look shiny, glazed or cracked slip and cause misfeeds. Replace them as a set so they wear evenly.