Tabber care: a daily, weekly and monthly checklist
A tabber is simple to run and easy to neglect. When tabs start landing early, late or not at all, the cause is usually one of three things: adhesive building up where the tab leaves the liner, a dusty sensor, or a transport belt that has started to slip. Five minutes a day keeps most of that from happening.
In short
- Daily: clear adhesive buildup, clean the sensors, check the web path, run test pieces.
- Weekly: inspect transport and feeder belts, clean out paper dust.
- Monthly: look over the wear parts and listen for new noises.
- Always: store tab rolls cool, dry and flat, and use the oldest first.
Every day (about five minutes)
| Check | Why it matters |
|---|---|
| Wipe adhesive from the tab path and the point where the tab peels off the liner, with power off | Buildup slowly throws placement off and causes tabs to fold or flag |
| Clean the product and tab sensors | A dusty sensor is the most common cause of tabs landing early, late or not at all |
| Check that the liner tracks straight through every guide | A web riding up a roller pulls tabs off target |
| Empty the liner take-up before it gets heavy | A full take-up drags the web and changes tension |
| Run test pieces at production speed and check placement | Catches a problem before 10,000 pieces do |
Every week
| Check | Why it matters |
|---|---|
| Transport belts: look for glazing, cracks or stretch | A slipping belt delivers the piece late, so the tab lands behind where it should |
| The feeder in front of the tabber: separator and feed belts | A feeder pulling doubles looks like a tabbing problem |
| Clear paper dust from inside covers and around the drive, power off | Dust works into sensors and bearings |
Every month
| Check | Why it matters |
|---|---|
| Wear parts: peel point, rollers, drive belts, anything rubber | Worn parts are cheap ahead of time and expensive on deadline |
| Listen under load for a new squeal or knock | Usually a bearing or belt giving warning before it fails |
| Compare current settings with the ones written down for each regular job | If a setting keeps creeping to hold placement, something is wearing |
Tab rolls: storage decides tack
Tab adhesive ages, and heat speeds that up. Keep rolls in their boxes, lying flat, in a cool, dry room away from radiators, windows and loading docks. Use the oldest rolls first. In winter, bring rolls and stock into the production room ahead of the job; cold adhesive and cold paper do not bond well. A roll that sat in a hot truck or near a heater can lose tack for good, and no machine adjustment fixes that.
When you order, give us the tabber model, the seal size and the material, and we match the roll and core. The USPS rules on size, material and perforation are in Wafer seals and tabs.
Placement problems: check in this order
- Clean the sensors.
- Rethread the web and empty the take-up.
- Check the transport belts for slip.
- Try a fresh roll from a different box.
- Only then change timing or offset settings.
Most placement drift is fixed by the first three steps. Changing settings first just moves the problem.
When to call
If cleaning and a fresh roll do not bring placement back, or the machine starts sounding different, call before it stops completely. A worn belt or roller ordered ahead is a short visit. Our technicians service Kirk-Rudy 535, 540 and 545 series tabbers and the other lines we carry; see tabber service.
Questions we get
Why are my tabs landing off the edge?
Most often a dusty or mis-set sensor, pieces slipping on worn transport belts, or a web that is tracking off its path. Clean the sensors, check the belts and rethread the web before changing any timing settings.
Why don't my tabs stick well?
Old or badly stored rolls lose tack, and cold or dusty pieces resist adhesion. Store rolls cool and dry, use the oldest rolls first, and let cold stock warm up to room temperature before the run.
How should tab rolls be stored?
In their boxes, lying flat, in a cool, dry room away from heat, radiators and sunlight. Use the oldest rolls first.
How long does tabber maintenance take?
The daily items take about five minutes. The weekly and monthly checks take longer but prevent most of the service calls we see.